Beats Flex is a high-quality pair of magnetic earbuds with premium features and on-device controls. When fully charged, these in-ear earphones provide up to 12 hours of listening time. Moreover, the earphones support quick charging. Charging the earbuds for 10 minutes provides an additional 1.5 hours of playback.
Thanks to their extended range, you can use them to listen to music and receive calls wirelessly without unnecessary dropouts. It also features an advanced microphone to help reduce background noise for enhanced voice clarity when answering or placing calls.
But even the best earphones are susceptible to malfunctions. Your Beats Flex might fail to turn on even when fully charged. This guide explains how to fix Beats Flex which won’t turn on.
Key Takeaways
- If you can’t turn on your Beats Flex, check the battery status. If the LED indicator on the earphones flashes red, the battery is critically low and requires a recharge.
- Your Beats Flex might malfunction and not turn on because of software bugs and technical glitches. Resetting the earphones can help resolve the issue.
- Dirt and gunk buildup might clog the power button causing your Beats Flex not to work. Cleaning your Beat Flex earphones can help fix the issue.
- Hardware issues caused by sweat and water damage can cause your Beats Flex to malfunction. If the problem is unrepairable, the only solution is to replace the earphones.
- Battery failure can cause your Beats Flex not to power on. Schedule a repair service with Apple to replace the faulty battery.
Recommended Reading :
Beats Flex Won’t Turn On – Potential Causes
Your Beats Flex earphones might not turn on because of a low charge, battery failure, or technical glitches. Firmware issues can also cause your earphones to malfunction.
Fortunately, fixing the problem doesn’t have to be complex. Here are the possible reasons your Beats Flex won’t turn on and how to fix them:
Incorrect Powering Procedure
Most high-end earbuds turn on automatically when taken out of their charging dock. However, the Beats Flex wireless earphones are different. They do not have a charging case, meaning the powering procedure differs from other earbuds. You must manually turn the earphones on by pressing the power button on the right control module.
Your Beats Flex might not turn on if you don’t power the earphones correctly. It’s easy to get it wrong, particularly if you’re a first-time buyer using the Beat Flex earphones for the first time.
Here’s how to power on your Beats Flex:
- Locate the power button on the right (R) control module.
- Press the power button and hold it for one or more seconds.
- Release the button when the LED indicator glows a white light.
- Your earphones are now ready for use.
Press the POWER button until the LED flashes white to turn Beats Flex on.
Low Charge
The Beats Flex earphones are wireless earbuds that operate with rechargeable batteries. The built-in battery provides up to 12 hours of playback time when fully charged. Depending on the frequency of use, you may have to recharge the battery sooner than expected. If not, your Beats Flex won’t turn on because of a low charge.
You can check your earphones’ battery level via the LED indicator or paired iPhone. The LED indicator blinks different lights to display the current battery status.
A white light means your earphones have more than one hour left, while a red light indicates the battery has less than one hour of charge. If the LED indicator blinks red, the battery is critically low and requires a recharge.
Your Beats Flex won’t turn on unless you recharge the depleted battery. Fortunately, the earphones support fast charging. A 10-minute charge will give you 1.5 hours of playback time.
If the battery is too low, your Beats Flex may refuse to turn on.
Battery Failure
Battery failure can cause your Beats Flex to malfunction and not turn on. Like most wireless earphones, the Beats Flex uses Lithium-ion batteries. If you didn’t know, these battery cells have a limited lifespan, not exceeding 300-500 charge cycles.
If you charge your earphones frequently, the battery might be past its best working state and can’t hold a charge anymore. The only solution is to replace the battery.
Your battery might be eligible for a replacement. However, you may have to pay a small fee unless you have an AppleCare+ subscription. Contact Apple to schedule a battery replacement service.
If the battery is dead, you may have to contact Apple to schedule a battery replacement (or buy new earphones).
Damaged Power Button
Your Beats Flex might not turn on because of a damaged power button. The power button is delicate and can get damaged from improper storage. Hard-pressing the switch can also cause irreversible damage, forcing you to schedule a repair service.
The good news is you can get a replacement switch from a local technician. Most earphones use a similar power button so finding a replacement should not be an issue. Alternatively, you can schedule a repair service with Apple at a small fee. The cost might vary depending on your warranty agreement.
If the power button is damaged/broken, you will either have to replace it or get new earphones.
Bugs & Glitches
It is usual for electronics to develop bugs and glitches during their lifetime. Your Beats Flex earbuds are no exception. Your Beats Flex earphones might malfunction because of software bugs. Your personalized settings can also cause the earphones to act up and fail to turn on.
Fortunately, fixing software bugs and glitches is straightforward. You only need to reset the earbuds to restore their functionality. A reset will also correct other issues and allow you to configure the earphones afresh.
Follow these steps to reset your Beats Flex earphones:
- Locate the power button on the right control module.
- Find the volume down button on the left control module.
- Press and hold power and volume down (-) buttons simultaneously.
- Keep pressing the buttons for 15 seconds to reset the earphones.
- Release the buttons when the LED flashes.
Pressing the POWER and VOL DOWN buttons simultaneously for 15 seconds will reset your Beats Flex.
Moisture Damage
Your Beats Flex might not turn on because of moisture damage. Even though the earphones have some level of water resistance, they are not waterproof. They don’t have a defined IPX rating, meaning excess exposure to moisture might damage them.
Exposure to moisture could damage your Beats Flex and prevent them from turning on.
Repairing your Beats Flex earphones depends on the extent of the damage. If excess moisture penetrates the earphones, the only option is to replace them.
You can schedule a repair service with Apple to establish if the earbuds are repairable. If the damage is irreversible, consider purchasing new Beats Flex earphones.
Dirty Earphones
Believe it or not, dirt and dust buildup can cause your Beats Flex not to turn on. If you often use your earphones outdoors, they might attract debris and external elements. The sediments might clog the power button, making it impossible to power your earphones.
Proper care and maintenance are necessary to ensure your Beats Flex earphones are clean and don’t develop issues. You can use a dry cloth to wipe dust and grease. Use a sharp pin to gently remove debris around the power button. Also, store your earphones in their carrying case to keep dirt and dust away.
Frequently Asked Questions
- Question: How do you turn on Beats Flex?
- Answer: Unlike other Beats earbuds that automatically turn on when removed from the charging dock, you must power on your Beats Flex in-ear earphones manually. Locate the power button on the right control module and press it for one or more seconds to turn on your Beats Flex earphones. The LED indicator will turn solid white if the earphones have sufficient charge and are ready for use.
- Question: Why are my Beats Flex earphones not turning on?
- Answer: Your Beats Flex earphones might not turn on for several reasons. First, check the battery level to determine if it is the cause of the problem. An inadequate battery charge might cause your earphones to malfunction. Charge the battery before trying again. If that doesn’t work, check the power button for dirt buildup and clean it.
- Question: Why won’t my Beats Flex turn on with a full battery?
- Answer: Your Beats Flex earphones might malfunction and fail to turn on even with a full battery. The battery might be past its best working state and can’t hold a charge anymore. Replacing the battery can help fix the issue. Contact Apple to schedule a battery replacement service. You may have to pay a small fee for the replacement unless you have an AppleCare+ subscription.
- Question: How do I know if my Beats Flex earphones are charging?
- Answer: Your Beats Flex earphones have an LED indicator that displays the current battery level and charging status. Plug a charger into the charging port and check the LED indicator. The LED will blink red when charging the earphones. When fully charged, the LED indicator will turn solid white.
- Question: How do I reset my Beats Flex?
- Answer: Your Beats Flex might not turn on because of a minor glitch or software bug. Resetting the earphones can help resolve the issue. Locate the power button on the right control module and the volume down button on the left control panel. Press and hold the power and volume down (-) buttons simultaneously for 15 seconds to reset the earphones. Release the buttons when the LED flashes.
Conclusion
Dealing with Beats Flex earphones that won’t turn on can leave you confused or even frustrated. Fortunately, you don’t have to fret if you can’t turn on Beats Flex. Start by checking the battery status to rule out the possibility of a low charge. If the earphones have adequate power and the problem persists, reset the earphones. Follow this simple but detailed guide for proven tips on fixing Beats Flex earphones that won’t turn on.
